Bring back the smooth, controlled ride your Model 3 had when it was new. The MEYLE front and rear shock absorber set replaces worn dampers on both axles with an upgraded design. Its damping is tuned for everyday comfort and steady, precise handling, and it's built tougher than the original parts to last longer.
Fits Tesla Model 3
Not for adaptive suspension
Front + rear axle set
Twin-tube gas pressure
Corrosion-resistant coating
Will this fit my Model 3?
This set fits Tesla Model 3 vehicles with the standard (passive) suspension. It does not fit vehicles equipped with Electronic Adaptive Suspension. You can also check your car's original part numbers against the Tesla OE references below. Still not sure? Contact our team with your VIN before ordering and we'll confirm fitment.
What's in the Box
- Front axle shock absorbers (left + right)
- Rear axle shock absorbers (left + right)
Sold as a complete set covering both axles.
What You'll Notice
- Bumps and broken pavement absorbed more smoothly
- Less float and wallow at highway speeds
- Tighter, more predictable steering response
- A quieter, more settled suspension overall
Time for New Shocks?
- The car keeps bouncing after a dip or bump
- The nose dips noticeably under braking
- Knocking or rattling over rough roads
- Oily residue on the shock body
Key Features
-
✓Comfort-focused damping that still keeps the car stable
-
✓Twin-tube, gas-pressure construction
-
✓Heavier piston rod and housing wall for a longer service life
-
✓Cathodic dip coating shields against rust and road salt
-
✓Extended rod thread and stronger fork speed up installation
-
✓Allows up to a 25 mm lower stance when paired with matching coil springs
Description
Over time, factory shocks lose their control, and the Model 3 starts to feel busy over bumps and loose on the highway. MEYLE built this set to fix that and improve on the original along the way. The valving is calibrated to take the edge off rough roads while keeping the car composed through corners and lane changes, so it feels refined on your commute and confident when you push it.
MEYLE also strengthened the areas that typically give out first. A larger piston rod and thicker housing wall add durability, and a cathodic dip coating protects the shocks from moisture and winter salt. For the installer, a longer rod thread and a sturdier fork make the job faster, whether it's done in a shop or at home.
Specifications
| Brand |
MEYLE-PD (Performance Design) |
| Product Type |
Front and rear shock absorber set |
| Fitment |
Tesla Model 3 with standard (passive) suspension |
| Does Not Fit |
Vehicles with Electronic Adaptive Suspension |
| Fitting Position |
Front axle and rear axle |
| Shock Type |
Gas pressure, twin-tube |
| Design |
Suspension strut and telescopic shock absorber |
| Mounting Type |
Top pin |
| Corrosion Protection |
Cathodic dip coating |
| Lowering Capability |
Up to 25 mm with corresponding coil springs |
| Tesla OE References |
1044092-00-A, 1044097-00-A, 1044363-00-G, 1044363-04-B, 1044363-04-C, 1044364-00-G, 1044364-01-F, 1044368-00-G, 1044368-04-B, 1044368-04-C, 1044369-00-G, 1044369-01-F |
Good to Know
-
Not compatible with Electronic Adaptive Suspension. Fits standard (passive) suspension only.
- Shocks should be replaced in pairs. This set covers both the front and rear axles.
- Lowering by up to 25 mm requires matching coil springs (sold separately).
- Professional installation and a wheel alignment afterward are recommended.
Ride Quality, Restored and Improved
Refresh all four corners of your Model 3 in one go. The MEYLE front and rear set delivers a calmer, more controlled ride that's built to hold up mile after mile.
Lifetime Replacement Eligible
